APRS Track Direct

My position About ☰

reset

M0IGA-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object M0IGA-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1789363554	634 Count	118 Count	111 Count
1789362054	633 Count	118 Count	111 Count
1789360553	632 Count	118 Count	111 Count
1789359053	631 Count	118 Count	111 Count
1789357552	630 Count	118 Count	111 Count
1789356051	629 Count	118 Count	111 Count
1789354550	628 Count	118 Count	111 Count
1789353050	627 Count	118 Count	111 Count
1789351549	626 Count	118 Count	111 Count
1789350048	625 Count	118 Count	111 Count
1789348548	624 Count	118 Count	111 Count
1789347047	623 Count	118 Count	111 Count
1789345546	622 Count	118 Count	111 Count
1789344045	621 Count	118 Count	111 Count
1789342545	620 Count	118 Count	111 Count
1789341044	619 Count	118 Count	111 Count
1789339544	618 Count	118 Count	111 Count
1789338043	617 Count	118 Count	111 Count
1789336542	616 Count	118 Count	111 Count
1789335041	615 Count	118 Count	111 Count
1789333541	614 Count	118 Count	111 Count
1789332040	613 Count	118 Count	111 Count
1789330539	612 Count	118 Count	111 Count
1789329039	611 Count	118 Count	111 Count
1789327538	610 Count	118 Count	111 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: