APRS Track Direct

My position About ☰

reset

F5ZMX-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F5ZMX-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1792559937	152 Count	359 Count	91 Count
1792559034	151 Count	355 Count	91 Count
1792558130	149 Count	351 Count	90 Count
1792557227	146 Count	345 Count	88 Count
1792556324	144 Count	341 Count	87 Count
1792555420	142 Count	336 Count	86 Count
1792554517	140 Count	334 Count	85 Count
1792553614	139 Count	328 Count	85 Count
1792552710	135 Count	321 Count	82 Count
1792551807	133 Count	315 Count	81 Count
1792550904	129 Count	308 Count	78 Count
1792550000	124 Count	300 Count	74 Count
1792549097	122 Count	295 Count	73 Count
1792548193	121 Count	289 Count	73 Count
1792547290	120 Count	284 Count	73 Count
1792546387	118 Count	277 Count	72 Count
1792545483	116 Count	274 Count	71 Count
1792544580	113 Count	267 Count	69 Count
1792543676	112 Count	264 Count	69 Count
1792543234	111 Count	264 Count	69 Count
1792542330	110 Count	256 Count	69 Count
1792541427	108 Count	249 Count	68 Count
1792540523	104 Count	243 Count	65 Count
1792539620	101 Count	237 Count	63 Count
1792538716	99 Count	230 Count	62 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: