APRS Track Direct

My position About ☰

reset

SP6TPX-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP6TPX-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1774024224	61 Count	888 Count	37 Count
1774022454	60 Count	830 Count	37 Count
1774020651	59 Count	783 Count	37 Count
1774018848	58 Count	744 Count	37 Count
1774017045	57 Count	703 Count	37 Count
1774015242	56 Count	634 Count	37 Count
1774013439	55 Count	597 Count	37 Count
1774011635	54 Count	550 Count	37 Count
1774009832	53 Count	477 Count	37 Count
1774008029	52 Count	436 Count	37 Count
1774006226	51 Count	410 Count	37 Count
1774004423	50 Count	372 Count	37 Count
1774002620	49 Count	346 Count	37 Count
1774002567	48 Count	344 Count	37 Count
1773994064	12 Count	209 Count	7 Count
1773992261	10 Count	177 Count	6 Count
1773990458	6 Count	131 Count	3 Count
1773988655	5 Count	97 Count	3 Count
1773986851	4 Count	72 Count	3 Count
1773985086	2 Count	38 Count	2 Count
1773983283	200 Count	1020 Count	172 Count
1773981480	199 Count	979 Count	172 Count
1773979676	196 Count	951 Count	170 Count
1773977873	195 Count	924 Count	170 Count
1773976070	192 Count	894 Count	168 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: