APRS Track Direct

My position About ☰

reset

SP6PTT Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP6PTT. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1782046303	77 Count	866 Count	73 Count
1782044502	53 Count	713 Count	50 Count
1782042702	41 Count	506 Count	39 Count
1782040901	29 Count	305 Count	28 Count
1782039100	7 Count	86 Count	7 Count
1782037299	100 Count	1010 Count	91 Count
1782035499	94 Count	916 Count	86 Count
1782033698	81 Count	806 Count	74 Count
1782031897	72 Count	693 Count	66 Count
1782030096	65 Count	597 Count	60 Count
1782028296	53 Count	460 Count	49 Count
1782026504	42 Count	363 Count	39 Count
1782024703	29 Count	244 Count	27 Count
1782022903	15 Count	106 Count	14 Count
1782021102	167 Count	1119 Count	159 Count
1782019301	147 Count	986 Count	140 Count
1782017500	129 Count	823 Count	123 Count
1782015699	110 Count	710 Count	105 Count
1782013898	89 Count	586 Count	85 Count
1782012097	74 Count	477 Count	71 Count
1782010296	53 Count	367 Count	51 Count
1782008496	33 Count	254 Count	32 Count
1782006695	17 Count	140 Count	17 Count
1782004903	152 Count	1120 Count	146 Count
1782003103	130 Count	992 Count	125 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: