APRS Track Direct

My position About ☰

reset

HB9EZW-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HB9EZW-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1775139972	514 Count	885 Count	112 Count
1775139069	513 Count	882 Count	112 Count
1775138166	511 Count	879 Count	111 Count
1775137333	510 Count	878 Count	111 Count
1775136430	509 Count	876 Count	111 Count
1775135527	507 Count	872 Count	110 Count
1775134624	505 Count	870 Count	109 Count
1775133721	503 Count	865 Count	108 Count
1775132818	502 Count	864 Count	108 Count
1775131915	501 Count	861 Count	108 Count
1775131012	499 Count	858 Count	107 Count
1775130109	498 Count	857 Count	107 Count
1775129206	496 Count	854 Count	106 Count
1775128303	495 Count	852 Count	106 Count
1775127400	493 Count	849 Count	105 Count
1775126497	492 Count	846 Count	105 Count
1775125594	491 Count	836 Count	105 Count
1775124690	490 Count	834 Count	105 Count
1775123787	489 Count	832 Count	105 Count
1775122884	488 Count	832 Count	105 Count
1775121981	487 Count	831 Count	105 Count
1775121078	486 Count	828 Count	105 Count
1775120175	485 Count	825 Count	105 Count
1775119272	484 Count	824 Count	105 Count
1775118369	483 Count	824 Count	105 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: