APRS Track Direct

My position About ☰

reset

SQ7FSO Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ7FSO. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1782056674	356 Count	170 Count	166 Count
1782056073	355 Count	170 Count	166 Count
1782055472	353 Count	169 Count	165 Count
1782054872	350 Count	168 Count	164 Count
1782054271	349 Count	168 Count	164 Count
1782053670	347 Count	167 Count	163 Count
1782053069	345 Count	166 Count	162 Count
1782052468	343 Count	166 Count	162 Count
1782051867	331 Count	155 Count	151 Count
1782051266	330 Count	155 Count	151 Count
1782050665	327 Count	154 Count	150 Count
1782050065	325 Count	153 Count	149 Count
1782049464	324 Count	153 Count	149 Count
1782048863	321 Count	152 Count	148 Count
1782048262	319 Count	151 Count	147 Count
1782047662	318 Count	151 Count	147 Count
1782047061	315 Count	150 Count	146 Count
1782046460	313 Count	149 Count	145 Count
1782045859	312 Count	149 Count	145 Count
1782045258	309 Count	148 Count	144 Count
1782044657	307 Count	147 Count	143 Count
1782044056	306 Count	147 Count	143 Count
1782043456	304 Count	146 Count	142 Count
1782042855	301 Count	145 Count	141 Count
1782042254	300 Count	145 Count	141 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: