APRS Track Direct

My position About ☰

reset

SP9KPS-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP9KPS-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1789341513	98 Count	776 Count	90 Count
1789339712	84 Count	680 Count	78 Count
1789337911	72 Count	574 Count	67 Count
1789336110	57 Count	477 Count	54 Count
1789334309	45 Count	376 Count	43 Count
1789332509	26 Count	254 Count	25 Count
1789330708	13 Count	120 Count	13 Count
1789328916	115 Count	1107 Count	103 Count
1789327115	105 Count	994 Count	95 Count
1789325315	94 Count	874 Count	85 Count
1789323514	79 Count	756 Count	71 Count
1789321713	68 Count	630 Count	62 Count
1789319912	55 Count	499 Count	50 Count
1789318112	38 Count	369 Count	35 Count
1789316311	26 Count	229 Count	24 Count
1789314510	12 Count	106 Count	11 Count
1789312709	152 Count	1078 Count	133 Count
1789310908	142 Count	969 Count	124 Count
1789309108	128 Count	846 Count	111 Count
1789303119	127 Count	846 Count	111 Count
1789301318	114 Count	748 Count	99 Count
1789283604	113 Count	748 Count	99 Count
1789281803	86 Count	641 Count	80 Count
1789280002	71 Count	520 Count	66 Count
1789278209	53 Count	396 Count	49 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: