APRS Track Direct

My position About ☰

reset

GM4HYG-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object GM4HYG-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1777442741	164 Count	166 Count	100 Count
1777441838	162 Count	165 Count	99 Count
1777440934	161 Count	165 Count	99 Count
1777440030	159 Count	164 Count	98 Count
1777439127	157 Count	163 Count	97 Count
1777438223	151 Count	158 Count	92 Count
1777437320	149 Count	157 Count	91 Count
1777436416	147 Count	156 Count	90 Count
1777435513	145 Count	155 Count	89 Count
1777434609	143 Count	154 Count	88 Count
1777433706	141 Count	153 Count	87 Count
1777432802	139 Count	152 Count	86 Count
1777431899	137 Count	151 Count	85 Count
1777430995	135 Count	150 Count	84 Count
1777430092	133 Count	149 Count	83 Count
1777429188	131 Count	148 Count	82 Count
1777428285	129 Count	147 Count	81 Count
1777427381	127 Count	146 Count	80 Count
1777426478	125 Count	145 Count	79 Count
1777425574	123 Count	144 Count	78 Count
1777424753	117 Count	143 Count	77 Count
1777423849	115 Count	142 Count	76 Count
1777422946	113 Count	141 Count	75 Count
1777422042	111 Count	140 Count	74 Count
1777421139	109 Count	139 Count	73 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: