APRS Track Direct

My position About ☰

reset

EA4CPM-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object EA4CPM-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TX*	RX*	Digi*
1770158520	182 Count	471 Count	127 Count
1770156716	177 Count	455 Count	123 Count
1770154913	170 Count	435 Count	117 Count
1770153110	168 Count	429 Count	116 Count
1770151345	167 Count	429 Count	116 Count
1770149541	154 Count	411 Count	104 Count
1770147738	151 Count	401 Count	102 Count
1770145935	150 Count	396 Count	102 Count
1770144132	147 Count	384 Count	100 Count
1770142328	145 Count	382 Count	99 Count
1770140525	144 Count	378 Count	99 Count
1770138722	143 Count	378 Count	99 Count
1770136919	142 Count	378 Count	99 Count
1770135115	141 Count	378 Count	99 Count
1770133312	140 Count	378 Count	99 Count
1770129744	138 Count	378 Count	99 Count
1770127940	137 Count	375 Count	99 Count
1770126137	136 Count	372 Count	99 Count
1770124334	134 Count	368 Count	98 Count
1770122531	131 Count	362 Count	96 Count
1770120727	128 Count	352 Count	94 Count
1770118924	122 Count	341 Count	89 Count
1770117121	115 Count	334 Count	83 Count
1770115318	114 Count	334 Count	83 Count
1770113514	113 Count	334 Count	83 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: