APRS Track Direct

My position About ☰

reset

SP3HUO-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP3HUO-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1782048576	257 Count	65 Count	59 Count
1782046775	253 Count	65 Count	59 Count
1782044999	249 Count	65 Count	59 Count
1782043198	244 Count	65 Count	59 Count
1782041397	239 Count	65 Count	59 Count
1782039595	235 Count	65 Count	59 Count
1782037795	230 Count	65 Count	59 Count
1782035993	220 Count	65 Count	59 Count
1782034192	214 Count	65 Count	59 Count
1782032390	210 Count	65 Count	59 Count
1782030589	206 Count	65 Count	59 Count
1782028788	202 Count	65 Count	59 Count
1782026987	198 Count	65 Count	59 Count
1782025186	194 Count	65 Count	59 Count
1782023385	187 Count	65 Count	59 Count
1782021584	183 Count	65 Count	59 Count
1782019783	176 Count	63 Count	57 Count
1782017981	170 Count	61 Count	55 Count
1782016180	162 Count	59 Count	53 Count
1782014379	156 Count	57 Count	51 Count
1782012578	150 Count	55 Count	49 Count
1782010777	144 Count	53 Count	47 Count
1782008976	138 Count	51 Count	45 Count
1782007174	132 Count	49 Count	43 Count
1782005374	126 Count	47 Count	41 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: