APRS Track Direct

My position About ☰

reset

SQ9SIM-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ9SIM-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1785284009	233 Count	93 Count	93 Count
1785280407	231 Count	93 Count	93 Count
1785276805	229 Count	93 Count	93 Count
1785273204	227 Count	93 Count	93 Count
1785269602	225 Count	93 Count	93 Count
1785266001	223 Count	93 Count	93 Count
1785262399	221 Count	93 Count	93 Count
1785258798	219 Count	93 Count	93 Count
1785255196	217 Count	93 Count	93 Count
1785251594	215 Count	93 Count	93 Count
1785248012	211 Count	91 Count	91 Count
1785244409	209 Count	91 Count	91 Count
1785240808	201 Count	85 Count	85 Count
1785237206	195 Count	81 Count	81 Count
1785233604	189 Count	77 Count	77 Count
1785230003	183 Count	73 Count	73 Count
1785226401	177 Count	69 Count	69 Count
1785222799	171 Count	65 Count	65 Count
1785219198	165 Count	61 Count	61 Count
1785215596	159 Count	57 Count	57 Count
1785211995	147 Count	47 Count	47 Count
1785208393	145 Count	47 Count	47 Count
1785204810	143 Count	47 Count	47 Count
1785201208	141 Count	47 Count	47 Count
1785197607	139 Count	47 Count	47 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: