APRS Track Direct

My position About ☰

reset

4K6AG-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 4K6AG-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1775175201	937 Count	115 Count	115 Count
1775174598	935 Count	114 Count	114 Count
1775173989	933 Count	113 Count	113 Count
1775173379	932 Count	113 Count	113 Count
1775172775	930 Count	112 Count	112 Count
1775171569	927 Count	111 Count	111 Count
1775169565	924 Count	109 Count	109 Count
1775168358	920 Count	107 Count	107 Count
1775167754	919 Count	107 Count	107 Count
1775167172	917 Count	106 Count	106 Count
1775166539	915 Count	105 Count	105 Count
1775165931	914 Count	105 Count	105 Count
1775165328	913 Count	105 Count	105 Count
1775164724	912 Count	105 Count	105 Count
1775164121	911 Count	105 Count	105 Count
1775163518	910 Count	105 Count	105 Count
1775162914	909 Count	105 Count	105 Count
1775162300	908 Count	105 Count	105 Count
1775160652	907 Count	105 Count	105 Count
1775160040	906 Count	105 Count	105 Count
1775159440	905 Count	105 Count	105 Count
1775158834	904 Count	105 Count	105 Count
1775158231	903 Count	105 Count	105 Count
1775157630	902 Count	105 Count	105 Count
1775157356	901 Count	105 Count	105 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: