APRS Track Direct

My position About ☰

reset

SP2WM-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP2WM-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1765494304	728 Count	140 Count	139 Count
1765493405	727 Count	140 Count	139 Count
1765491620	721 Count	140 Count	139 Count
1765490719	720 Count	140 Count	139 Count
1765489818	719 Count	140 Count	139 Count
1765488017	717 Count	140 Count	139 Count
1765487117	716 Count	140 Count	139 Count
1765485314	714 Count	140 Count	139 Count
1765484414	713 Count	140 Count	139 Count
1765483513	712 Count	140 Count	139 Count
1765482612	711 Count	140 Count	139 Count
1765481711	710 Count	140 Count	139 Count
1765480811	709 Count	140 Count	139 Count
1765479910	708 Count	140 Count	139 Count
1765479009	707 Count	140 Count	139 Count
1765478108	706 Count	140 Count	139 Count
1765477207	705 Count	140 Count	139 Count
1765475406	703 Count	140 Count	139 Count
1765474505	702 Count	140 Count	139 Count
1765473604	701 Count	140 Count	139 Count
1765471804	699 Count	140 Count	139 Count
1765470920	694 Count	140 Count	139 Count
1765470019	693 Count	140 Count	139 Count
1765469119	692 Count	140 Count	139 Count
1765466416	689 Count	140 Count	139 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: