APRS Track Direct

My position About ☰

reset

SQ2MO Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ2MO. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1792532895	145 Count	794 Count	61 Count
1792532295	144 Count	790 Count	61 Count
1792531694	143 Count	783 Count	61 Count
1792531315	138 Count	777 Count	61 Count
1792530715	137 Count	773 Count	61 Count
1792530114	136 Count	767 Count	61 Count
1792529513	135 Count	758 Count	61 Count
1792528912	134 Count	754 Count	61 Count
1792528312	133 Count	742 Count	61 Count
1792525308	128 Count	707 Count	61 Count
1792524106	126 Count	693 Count	61 Count
1792523505	125 Count	687 Count	61 Count
1792522905	124 Count	681 Count	61 Count
1792522304	123 Count	674 Count	61 Count
1792521703	122 Count	672 Count	61 Count
1792521102	121 Count	669 Count	61 Count
1792520502	120 Count	663 Count	61 Count
1792519901	119 Count	662 Count	61 Count
1792519300	118 Count	660 Count	61 Count
1792518700	114 Count	652 Count	58 Count
1792518098	113 Count	650 Count	58 Count
1792517498	112 Count	644 Count	58 Count
1792516897	111 Count	640 Count	58 Count
1792516296	110 Count	637 Count	58 Count
1792515695	109 Count	634 Count	58 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: