APRS Track Direct

My position About ☰

reset

SP9APJ-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP9APJ-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1770204432	108 Count	902 Count	93 Count
1770200831	93 Count	754 Count	80 Count
1770199030	86 Count	710 Count	74 Count
1770197230	80 Count	648 Count	69 Count
1770195429	72 Count	567 Count	62 Count
1770193629	59 Count	480 Count	50 Count
1770191828	50 Count	397 Count	42 Count
1770190027	41 Count	304 Count	34 Count
1770188227	29 Count	216 Count	23 Count
1770186426	19 Count	144 Count	14 Count
1770184632	6 Count	61 Count	6 Count
1770182831	125 Count	1052 Count	111 Count
1770181031	113 Count	972 Count	100 Count
1770179230	103 Count	898 Count	91 Count
1770177429	93 Count	813 Count	82 Count
1770175629	85 Count	709 Count	75 Count
1770172027	58 Count	504 Count	50 Count
1770170227	45 Count	382 Count	38 Count
1770168426	34 Count	285 Count	28 Count
1770166626	23 Count	196 Count	18 Count
1770164825	14 Count	93 Count	10 Count
1770163031	131 Count	1084 Count	115 Count
1770161230	123 Count	993 Count	108 Count
1770159430	113 Count	893 Count	99 Count
1770157629	104 Count	796 Count	91 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: