APRS Track Direct

My position About ☰

reset

SP9APJ-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP9APJ-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1765988175	22 Count	146 Count	14 Count
1765986374	18 Count	118 Count	11 Count
1765984574	14 Count	74 Count	8 Count
1765982773	9 Count	39 Count	4 Count
1765979178	111 Count	973 Count	89 Count
1765977378	106 Count	922 Count	85 Count
1765975577	100 Count	878 Count	80 Count
1765968375	77 Count	721 Count	61 Count
1765966574	73 Count	667 Count	58 Count
1765964773	68 Count	604 Count	54 Count
1765962973	61 Count	555 Count	48 Count
1765961172	54 Count	518 Count	42 Count
1765957577	38 Count	418 Count	32 Count
1765955777	32 Count	369 Count	27 Count
1765953976	28 Count	321 Count	24 Count
1765950375	13 Count	208 Count	11 Count
1765948575	8 Count	137 Count	7 Count
1765944973	67 Count	1068 Count	55 Count
1765943172	63 Count	987 Count	52 Count
1765941372	58 Count	915 Count	48 Count
1765937771	45 Count	662 Count	37 Count
1765934176	27 Count	340 Count	25 Count
1765932375	19 Count	222 Count	18 Count
1765928774	95 Count	1077 Count	78 Count
1765926974	87 Count	951 Count	71 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: