APRS Track Direct

My position About ☰

reset

SR8ULZ-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR8ULZ-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1765494374	250 Count	123 Count	123 Count
1765490773	248 Count	123 Count	123 Count
1765488972	247 Count	123 Count	123 Count
1765487178	242 Count	123 Count	123 Count
1765485377	241 Count	123 Count	123 Count
1765483577	240 Count	123 Count	123 Count
1765474575	235 Count	123 Count	123 Count
1765463777	225 Count	123 Count	123 Count
1765458375	222 Count	123 Count	123 Count
1765456574	221 Count	123 Count	123 Count
1765454774	220 Count	123 Count	123 Count
1765452973	219 Count	123 Count	123 Count
1765451173	218 Count	123 Count	123 Count
1765449372	217 Count	123 Count	123 Count
1765447572	216 Count	123 Count	123 Count
1765445771	215 Count	123 Count	123 Count
1765443977	207 Count	120 Count	120 Count
1765442176	203 Count	117 Count	117 Count
1765440375	199 Count	114 Count	114 Count
1765438575	191 Count	107 Count	107 Count
1765436774	188 Count	105 Count	105 Count
1765434973	180 Count	98 Count	98 Count
1765433173	178 Count	97 Count	97 Count
1765431372	177 Count	97 Count	97 Count
1765429572	175 Count	96 Count	96 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: