APRS Track Direct

My position About ☰

reset

SR8ULZ-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR8ULZ-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1787090681	300 Count	145 Count	145 Count
1787088880	298 Count	144 Count	144 Count
1787087080	296 Count	143 Count	143 Count
1787085279	294 Count	142 Count	142 Count
1787083478	292 Count	141 Count	141 Count
1787081677	290 Count	140 Count	140 Count
1787079877	288 Count	139 Count	139 Count
1787078076	286 Count	138 Count	138 Count
1787076282	280 Count	137 Count	137 Count
1787074482	278 Count	136 Count	136 Count
1787072681	276 Count	135 Count	135 Count
1787070884	274 Count	134 Count	134 Count
1787069080	260 Count	121 Count	121 Count
1787067279	254 Count	116 Count	116 Count
1787065479	251 Count	114 Count	114 Count
1787063678	249 Count	113 Count	113 Count
1787061877	247 Count	112 Count	112 Count
1787060077	245 Count	111 Count	111 Count
1787058276	243 Count	110 Count	110 Count
1787056475	241 Count	109 Count	109 Count
1787054681	235 Count	108 Count	108 Count
1787052881	233 Count	107 Count	107 Count
1787051080	231 Count	106 Count	106 Count
1787049280	229 Count	105 Count	105 Count
1787047479	227 Count	104 Count	104 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: