APRS Track Direct

My position About ☰

reset

SP6RJ-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP6RJ-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1785067725	313 Count	118 Count	118 Count
1785065916	304 Count	118 Count	118 Count
1785058679	267 Count	117 Count	117 Count
1785058077	258 Count	111 Count	111 Count
1785057581	249 Count	109 Count	109 Count
1785056978	246 Count	109 Count	109 Count
1785055772	240 Count	109 Count	109 Count
1785053365	226 Count	109 Count	109 Count
1785047936	185 Count	95 Count	95 Count
1785046127	174 Count	93 Count	93 Count
1785043715	156 Count	87 Count	87 Count
1785040700	114 Count	60 Count	60 Count
1785035992	70 Count	43 Count	43 Count
1785014837	866 Count	116 Count	100 Count
1785013365	849 Count	115 Count	99 Count
1785012158	843 Count	115 Count	99 Count
1785011555	840 Count	115 Count	99 Count
1785010349	834 Count	115 Count	99 Count
1785009143	828 Count	115 Count	99 Count
1785008540	825 Count	115 Count	99 Count
1785007937	822 Count	115 Count	99 Count
1785007334	819 Count	115 Count	99 Count
1785006236	809 Count	115 Count	99 Count
1785005030	798 Count	110 Count	94 Count
1785004426	795 Count	108 Count	94 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: