APRS Track Direct

My position About ☰

reset

SQ4HSE-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ4HSE-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1770154143	153 Count	310 Count	101 Count
1770150542	150 Count	308 Count	99 Count
1770146941	148 Count	307 Count	98 Count
1770143340	146 Count	303 Count	97 Count
1770139739	144 Count	302 Count	96 Count
1770136138	141 Count	300 Count	94 Count
1770132538	139 Count	295 Count	93 Count
1770128936	136 Count	275 Count	91 Count
1770125335	133 Count	246 Count	89 Count
1770121734	130 Count	213 Count	87 Count
1770118133	127 Count	190 Count	85 Count
1770114532	124 Count	179 Count	83 Count
1770110931	121 Count	175 Count	81 Count
1770107330	118 Count	170 Count	79 Count
1770103729	115 Count	167 Count	77 Count
1770100128	112 Count	165 Count	75 Count
1770096527	109 Count	163 Count	73 Count
1770092926	106 Count	160 Count	71 Count
1770089325	103 Count	158 Count	69 Count
1770085723	100 Count	156 Count	67 Count
1770082123	97 Count	154 Count	65 Count
1770078522	94 Count	152 Count	63 Count
1770074921	91 Count	150 Count	61 Count
1770071320	88 Count	148 Count	59 Count
1770067720	85 Count	146 Count	57 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: