APRS Track Direct

My position About ☰

reset

SR2DTW-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR2DTW-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1783160585	160 Count	117 Count	22 Count
1783158904	159 Count	113 Count	22 Count
1783157223	158 Count	110 Count	22 Count
1783155543	157 Count	106 Count	22 Count
1783153862	156 Count	104 Count	22 Count
1783152181	155 Count	103 Count	22 Count
1783150749	150 Count	103 Count	22 Count
1783149068	149 Count	103 Count	22 Count
1783147388	148 Count	100 Count	22 Count
1783145707	147 Count	99 Count	22 Count
1783144026	146 Count	95 Count	22 Count
1783142345	145 Count	94 Count	22 Count
1783140665	144 Count	91 Count	22 Count
1783138984	143 Count	90 Count	22 Count
1783137303	142 Count	89 Count	22 Count
1783135622	141 Count	88 Count	22 Count
1783133942	140 Count	88 Count	22 Count
1783132261	139 Count	82 Count	22 Count
1783130580	138 Count	81 Count	22 Count
1783129148	133 Count	77 Count	22 Count
1783127467	132 Count	75 Count	22 Count
1783125787	131 Count	72 Count	22 Count
1783124106	130 Count	70 Count	22 Count
1783122425	129 Count	69 Count	22 Count
1783120744	128 Count	68 Count	22 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: