APRS Track Direct

My position About ☰

reset

SP2OSA-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP2OSA-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1793307293	758 Count	108 Count	99 Count
1793306393	757 Count	108 Count	99 Count
1793305491	756 Count	108 Count	99 Count
1793304591	755 Count	108 Count	99 Count
1793303690	754 Count	108 Count	99 Count
1793302789	753 Count	108 Count	99 Count
1793301888	752 Count	108 Count	99 Count
1793300987	751 Count	108 Count	99 Count
1793300086	750 Count	108 Count	99 Count
1793299185	749 Count	108 Count	99 Count
1793298284	748 Count	108 Count	99 Count
1793297383	747 Count	108 Count	99 Count
1793296503	746 Count	108 Count	99 Count
1793295602	745 Count	108 Count	99 Count
1793294701	744 Count	108 Count	99 Count
1793293801	743 Count	108 Count	99 Count
1793292900	742 Count	108 Count	99 Count
1793291998	741 Count	108 Count	99 Count
1793291097	740 Count	108 Count	99 Count
1793290196	739 Count	108 Count	99 Count
1793289295	738 Count	108 Count	99 Count
1793288394	737 Count	108 Count	99 Count
1793287493	736 Count	108 Count	99 Count
1793286592	735 Count	108 Count	99 Count
1793285691	734 Count	108 Count	99 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: