APRS Track Direct

My position About ☰

reset

SQ9ITQ-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ9ITQ-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1771008015	759 Count	62 Count	62 Count
1771006215	758 Count	62 Count	62 Count
1771004414	757 Count	62 Count	62 Count
1771002613	756 Count	62 Count	62 Count
1771000813	755 Count	62 Count	62 Count
1770999012	754 Count	62 Count	62 Count
1770997212	753 Count	62 Count	62 Count
1770995411	747 Count	57 Count	57 Count
1770972017	719 Count	42 Count	42 Count
1770970216	718 Count	42 Count	42 Count
1770968416	717 Count	42 Count	42 Count
1770966615	716 Count	42 Count	42 Count
1770964814	710 Count	37 Count	37 Count
1770963014	709 Count	37 Count	37 Count
1770961213	708 Count	37 Count	37 Count
1770959412	707 Count	37 Count	37 Count
1770957612	706 Count	37 Count	37 Count
1770955811	705 Count	37 Count	37 Count
1770954011	704 Count	37 Count	37 Count
1770952210	703 Count	37 Count	37 Count
1770928816	690 Count	37 Count	37 Count
1770927016	689 Count	37 Count	37 Count
1770925215	688 Count	37 Count	37 Count
1770923414	687 Count	37 Count	37 Count
1770921614	686 Count	37 Count	37 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: