APRS Track Direct

My position About ☰

reset

SP5MSV-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP5MSV-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1789384270	671 Count	154 Count	32 Count
1789382469	670 Count	154 Count	32 Count
1789380669	669 Count	154 Count	32 Count
1789378868	668 Count	154 Count	32 Count
1789377067	667 Count	154 Count	32 Count
1789375267	666 Count	154 Count	32 Count
1789373466	665 Count	154 Count	32 Count
1789371665	664 Count	154 Count	32 Count
1789369864	663 Count	154 Count	32 Count
1789368072	662 Count	154 Count	32 Count
1789366271	661 Count	154 Count	32 Count
1789364470	660 Count	154 Count	32 Count
1789362670	659 Count	154 Count	32 Count
1789360869	658 Count	154 Count	32 Count
1789359068	657 Count	154 Count	32 Count
1789357268	656 Count	154 Count	32 Count
1789355467	655 Count	154 Count	32 Count
1789353666	654 Count	154 Count	32 Count
1789351865	653 Count	154 Count	32 Count
1789350065	652 Count	154 Count	32 Count
1789348264	651 Count	154 Count	32 Count
1789346471	650 Count	154 Count	32 Count
1789344671	649 Count	154 Count	32 Count
1789342870	648 Count	154 Count	32 Count
1789341069	647 Count	154 Count	32 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: