APRS Track Direct

My position About ☰

reset

F4FWW-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F4FWW-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1792575429	308 Count	215 Count	211 Count
1792573629	277 Count	185 Count	181 Count
1792571828	276 Count	185 Count	181 Count
1792570027	275 Count	185 Count	181 Count
1792568227	274 Count	185 Count	181 Count
1792566426	273 Count	185 Count	181 Count
1792564625	264 Count	177 Count	173 Count
1792562825	239 Count	153 Count	149 Count
1792561024	229 Count	144 Count	140 Count
1792537630	216 Count	144 Count	140 Count
1792535829	215 Count	144 Count	140 Count
1792534029	214 Count	144 Count	140 Count
1792532228	213 Count	144 Count	140 Count
1792530427	212 Count	144 Count	140 Count
1792528627	211 Count	144 Count	140 Count
1792526826	210 Count	144 Count	140 Count
1792525025	209 Count	144 Count	140 Count
1792523224	208 Count	144 Count	140 Count
1792521424	207 Count	144 Count	140 Count
1792519623	206 Count	144 Count	140 Count
1792517822	205 Count	144 Count	140 Count
1792516029	204 Count	144 Count	140 Count
1792514229	203 Count	144 Count	140 Count
1792512428	202 Count	144 Count	140 Count
1792510627	201 Count	144 Count	140 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: