APRS Track Direct

My position About ☰

reset

SP4HMU-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP4HMU-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1787076414	3 Count	19 Count	2 Count
1787075814	1 Count	11 Count	1 Count
1787075213	114 Count	1005 Count	45 Count
1787074613	113 Count	998 Count	45 Count
1787074012	111 Count	989 Count	44 Count
1787073411	109 Count	975 Count	43 Count
1787072811	108 Count	968 Count	43 Count
1787072210	106 Count	958 Count	42 Count
1787071609	104 Count	945 Count	41 Count
1787071009	103 Count	937 Count	41 Count
1787070408	101 Count	913 Count	40 Count
1787069807	99 Count	897 Count	39 Count
1787069206	98 Count	880 Count	39 Count
1787068606	96 Count	864 Count	38 Count
1787068005	94 Count	849 Count	37 Count
1787067405	93 Count	838 Count	37 Count
1787066804	91 Count	824 Count	36 Count
1787066203	89 Count	809 Count	35 Count
1787065603	88 Count	796 Count	35 Count
1787065002	86 Count	784 Count	34 Count
1787064401	84 Count	769 Count	33 Count
1787063801	83 Count	759 Count	33 Count
1787063200	81 Count	746 Count	32 Count
1787062599	79 Count	729 Count	31 Count
1787061999	78 Count	718 Count	31 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: