APRS Track Direct

My position About ☰

reset

LW2DHT-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LW2DHT-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	Digi*
1764930957	193 Count	153 Count	147 Count
1764929154	189 Count	150 Count	144 Count
1764927351	185 Count	147 Count	141 Count
1764925547	182 Count	145 Count	139 Count
1764923744	178 Count	142 Count	136 Count
1764921941	174 Count	139 Count	133 Count
1764920138	171 Count	137 Count	131 Count
1764918334	167 Count	134 Count	128 Count
1764916571	163 Count	131 Count	125 Count
1764914768	158 Count	128 Count	122 Count
1764912965	154 Count	125 Count	119 Count
1764911161	150 Count	122 Count	116 Count
1764909358	146 Count	119 Count	113 Count
1764907555	142 Count	116 Count	110 Count
1764905751	138 Count	114 Count	108 Count
1764903948	136 Count	113 Count	107 Count
1764902144	133 Count	111 Count	105 Count
1764900341	129 Count	108 Count	102 Count
1764898538	125 Count	105 Count	99 Count
1764896734	121 Count	102 Count	96 Count
1764895574	119 Count	101 Count	95 Count
1764893771	115 Count	98 Count	92 Count
1764891967	113 Count	97 Count	91 Count
1764890164	109 Count	94 Count	88 Count
1764888360	105 Count	91 Count	85 Count

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Select date and time to show map data for (enter time for your locale time zone). The regular time length select box can still be used to select how old data that should be shown (relative to selected date and time).

*Note that the heatmap will still based on data from the latest hour (not the selected date and time).

Date and time: